Pinouts : Wizard of Wor (PCB) Version 0.1
Zurück zur Übersicht.

Übersicht
Dip Settings
Pinout (EN)
Pinout (DE)
Wizard of Wor Manual (PDF, 15,8MB)


Option Switch Settings
Wizard of Wor
Bally/Midway, June 1981

                                 Wizard of Wor
                            Option Switch Settings

-------------------------------------------------------------------------------
Option switches are located on the game PCB in the commercial card rack.
 1   2   3   4   5   6   7   8    Option
-------------------------------------------------------------------------------
                                  Left Hand Coin Slot
                                  -------------------
Off                               1 Coin  1 Credit
On                                2 Coins 1 Credit

                                  Right Hand Coin Slot
                                  --------------------
    Off Off                       1 Coin  1 Credit
    On  Off                       2 Coins 1 Credit
    Off On                        1 Coin  3 Credits
    On  On                        1 Coin  5 Credits

                                  Language
                                  --------
            Off                   English
            On                    Foreign Language
                                  (Requires A082-91374-A000)

                                  Worriors Per Credit
                                  -------------------
                Off               1 Credit = 2 Worriors/2 Credits = 5 Worriors
                On                1 Credit = 3 Worriors/2 Credits = 7 Worriors

                                  Bonus Player Awarded
                                  --------------------
                    Off           Bonus Worrior after third dungeon
                    On            Bonus Worrior after fourth dungeon

                                  Play Mode
                                  ---------
                        Off       Coin Play
                        On        Free Play

                                  Game Attraction Sounds
                                  ----------------------
                            Off   Continuous sound during "attract mode"
                            On    Sound during attract mode _only_ if game
                                  controls are touched.  (When any button
                                  or control is touched, game provides sound
                                  for one complete cycle of the "attract mode".
                                  It will then be quiet until touched again.)
-------------------------------------------------------------------------------

Special Note:

When setting the switches SW#1, SW#2, and SW#3 to either of the following two
combinations, _only coin meter number 1 will count_.

SW#1  SW#2  SW#3
Off   Off   Off
On    On    On

If the above three switches are set to any other combination, coin acceptor
number 1 will cause coin meter number 1 to count and coin acceptor number 2
will cause coin meter number 2 to count.


Pinout (EN)
Wizard of Wor pinouts
Midway, 1981
 
There are nine boards in the Wizard of Wor boardset:
Qty                                                Position on
                                                   Motherboard
1 *Game Bd                 A084-90708-A961             J6
1 *Memory Bd (ROM/RAM)     A082-91397-A000             J5
1  Pattern Bd              A082-91348-0000             J4
1  CPU Bd (C.P.U.)         A082-91354-F000             J3
2  RAM Card                A082-91356-C000           J2 & J1
 
1  Comm. Mother Bd         A082-90006-B/C000
1  RGB Interface Board     A082-91363-A/B000
1 *Audio Amp #2            A084-90907-A961
 
With the exception of those boards marked with an asterisk (*), the rest of
the boards are used by at least two other Midway games -- Gorf and Space Zap.
All three of these games -- Space Zap, Wizard of Wor, and Gorf -- also share
the same power supply (A082-90411-A000).
 
Unfortunately, each of these games uses completely different pinouts on the
main Game board.  Also, Wizard of Wor uses a different amp board (the Audio
Amp #2 vs. the regular Audio Amp board) because it uses three speakers.  Gorf
and Space Zap can only use 2 speakers.  The power supply outputs from the
motherboard are the same for all these games, which means if you have the
power supply and the motherboard, you have all the power requirements for any
one of these games taken care of.
 
The "Position on Motherboard" column refers to the fact that these boards
plug into a common motherboard much like ISA/EISA/VESA/PCI cards plug into
PC card expansion slots.
 
Legend:
PS = Power Supply
IB = RGB Interface Board
AA = Audio Amp Board
GB = Game Board
 
 
Motherboard (9-pos, 0.156") (outputs & inputs from power supply)
Pin | Definition
------------------
  1 | +5V
  2 | +5V
  3 | +12V
  4 | !Reset
  5 | -5V
  6 | Key
  7 | Gnd
  8 | Gnd
  9 | -Sense (Gnd)
 
 
P1 CPU Board (24-pos, 0.100")
Pin | Definition
------------------
  1 | P2 Up
  2 | P2 Down
  3 | P2 Left
  4 | P2 Right
  5 | P2 Move
  6 | P2 Fire
  7 | Not Used
  8 | P1 Up
  9 | P1 Down
 10 | P1 Left
 11 | P1 Right
 12 | P1 Move
 13 | P1 Fire
 14 | Gnd (common return for all buttons & controls)
 15 | Key
 16 | Coin #1
 17 | Coin #2
 18 | Not Used
 19 | Test Sw. (in test mode when switch closed, else game mode)
 20 | Tilt
 21 | 1P Select
 22 | 2P Select
 23 | Gnd (common return for Coin, Tilt, and Test Sw.)
 24 | Not Used
 
 
P2 CPU Board (23-pos, 0.100")
Pin | Definition
------------------
  1 | Audio In #3 [to AA-4]
  2 | Audio In #1 [to AA-2]
  3 | Audio In #2 [to AA-3]
  4 | Audio Common [from AA-6]
  5 | Key
  6 | Coin Meter #1
  7 | Coin Meter #2
  8 | Not Used
  9 | Gnd [to PS]
 10 | Not Used
 11 | Key
 12 | Not Used
 13 | Not Used
 14 | +12V [to IB-2]
 15 | -5V [to IB-4]
 16 | +5V [to IB-5]
 17 | Gnd [from IB-1]
 18 | Blue [to IB-7]
 19 | Gnd [to IB-8]
 20 | Red [to IB-9]
 21 | Gnd [to IB-10]
 22 | Video (Green + -Sync?) [to IB-11]
 23 | Gnd [to IB-12]
 
 
RGB Interface Board (12-pos, 0.100"?)
(to & from Game Board)
Pin | Definition
------------------
  1 | Gnd
  2 | +12V
  3 | +12V
  4 | -5V
  5 | +5V
  6 | Key
  7 | Blue
  8 | Gnd
  9 | Red
 10 | Gnd
 11 | Video (Green + -Sync?)
 12 | Gnd
 
Note: Pins 7 & 8, 9 & 10, and 11 & 12 are labeled as "twisted pair" on the
schematic for the RGB Interface Board.
 
 
RGB Interface Board (9-pos, 0.100"?)
(to & from Monitor)
Pin | Definition
------------------
  1 | Gnd [to monitor RGB Gnd]
  2 | Red
  3 | Key
  4 | Gnd
  5 | Green
  6 | Gnd
  7 | Blue
  8 | Gnd [to monitor Sync Gnd]
  9 | -Sync
 
Note: Pins 1 & 2, 4 & 5, 6 & 7, and 8 & 9 are labeled "twisted pair" on the
schematic for the RGB Interface Board.
 
 
Audio Amp #2 Board (13-pos, 0.100"?)
(to & from Game Board)
Pin | Definition
------------------
  1 | Audio Return (+16V Gnd) [to PS]
  2 | Audio In #1
  3 | Audio In #2
  4 | Audio In #3
  5 | Key
  6 | Audio Common (common return from speakers)
  7 | +16V [from PS]
  8 | Speaker #1
  9 | Speaker #1
 10 | Speaker #2
 11 | Speaker #2
 12 | Speaker #3
 13 | Speaker #3
 
 
Here is most of the information for the power supply pinouts on the game
side of the power supply (A082-90411-0000).  A question mark indicates
information I was not absolutely sure about.  This power supply uses almost
exactly the same outputs and inputs as the one in Super Pac-Man (A082-
90421-0000).
 
Power Supply (19-pos?)
1   +V Audio (~13V @ 1.5A)
2   -5V @ 0.45A
3   +V Independent [~10V @ 3.5A, to coin door and control lights?]
4   !Reset
5   V.Batt?
6   Key
7   +12V @ 1.45A
8   +12V @ 1.45A
9   -Sense
10  AC Sync?
11  -V Audio [Gnd for Audio circuit]
12  -V Independent [Gnd, control lights return?]
13  Gnd
14  Gnd
15  Gnd
16  Gnd
17  Coin Counter Drivers (~8V, unreg +5V) [from coin meter]
18  +5V @ 3A
19  +5V @ 2A regulated for logic
 
Feel free to correct any misinformation you find in this pinout.  If you
let me know (holcomb@halcyon.com), I will correct the copy of this pinout
located on wiretap.spies.com.
 
--Dave Holcomb


Pinout (DE)
-=Wizard of Wor (Midway, 1981)=-
###PINOUTS (D)###

 
Es gibt insgesamt 9 PCB im WoW Boardset:

Anzahl	Funktion		Spare-No.	Position
1	*Game Bd		A084-90708-A961   J6
1	*Memory Bd (ROM/RAM)	A082-91397-A000	  J5
1	Pattern Bd		A082-91348-0000	  J4
1	CPU Bd			A082-91354-F000	  J3
2	RAM Card		A082-91356-C000	J2 & J1

1	Comm. Mother Bd		A082-90006-B/C000
1	RGB Interface Board	A082-91363-A/B000
1	*Audio Amp #2		A084-90907-A961

Mit Ausnahme der Boards, die mit einem * gekennzeichnet sind, werden die Boards
in zumindest 2 anderen Midway Games genutzt - Gorf und Space Zap.
Alle 3 Games (Space Zap, Wizard of Wor und Gorf, teilen sich auch das gleiche
Netzteil (Spare: A082-90411-A000).

Unglücklicherweise habt jedes dieser Games ein komplett anderes Pinout des
eigentlichen Gameboards. Des weiteren nutzt WoW ein anderes Verstärker-Board
(Amp #2 - Spare:A084-90907-A961) im Gegensatz zum normalen Verstärker-Board),
da es 3 Lautsprecher unterstützt. Gorf und Space Zap nutzen nur 2 Lautsprecher.
Die Ausgänge der PSU sein bei allen 3 Games gleich - sofern also das Grundboard
und die PSU vorhanden sind hat man alle voraussetzungen um alle 3 Games im Cab
betreiben zu können.

Die "Position"-Reihe bezieht sich auf die Tatsache, das die Boards in ein
Grundboard gesteckt werden - ähnlich wie ISA/EISA/VESA/PCI-Karten in ihre
entsprechenden Slots gesteckt werden.
 
Legende:
PS = Power Supply (Netzteil)
IB = RGB Interface Board
AA = Audio Amp Board
GB = Game Board
 
Grundboard (9-pos, 0.156") (Ein- und Ausgänge der PSU)
Pin | Definition
------------------
  1 | +5V
  2 | +5V
  3 | +12V
  4 | !Reset
  5 | -5V
  6 | Key
  7 | Gnd
  8 | Gnd
  9 | -Sense (Gnd)
 
 
P1 CPU Board (24-pos, 0.100")
Pin | Definition
------------------
  1 | P2 Up
  2 | P2 Down
  3 | P2 Left
  4 | P2 Right
  5 | P2 Move
  6 | P2 Fire
  7 | Not Used
  8 | P1 Up
  9 | P1 Down
 10 | P1 Left
 11 | P1 Right
 12 | P1 Move
 13 | P1 Fire
 14 | Gnd (GND für alle Schalter und Eingabegeräte)
 15 | Key
 16 | Coin #1
 17 | Coin #2
 18 | Not Used
 19 | Test Switch (geschlossen=Testmodus / offen=Spielmodus)
 20 | Tilt
 21 | 1P Select
 22 | 2P Select
 23 | Gnd (GND für Coin/Tilt/Test)
 24 | Not Used
 
 
P2 CPU Board (23-pos, 0.100")
Pin | Definition
------------------
  1 | Audio In #3 [to AA-4]
  2 | Audio In #1 [to AA-2]
  3 | Audio In #2 [to AA-3]
  4 | Audio Common (GND) [from AA-6]
  5 | Key
  6 | Coin Meter #1
  7 | Coin Meter #2
  8 | Not Used
  9 | Gnd [to PS]
 10 | Not Used
 11 | Key
 12 | Not Used
 13 | Not Used
 14 | +12V [to IB-2]
 15 | -5V [to IB-4]
 16 | +5V [to IB-5]
 17 | Gnd [from IB-1]
 18 | Blue [to IB-7]
 19 | Gnd [to IB-8]
 20 | Red [to IB-9]
 21 | Gnd [to IB-10]
 22 | Video (Green + -Sync?) [to IB-11]
 23 | Gnd [to IB-12]
 
 
RGB Interface Board (12-pos, 0.100"?)
(to & from Game Board)
Pin | Definition
------------------
  1 | Gnd
  2 | +12V
  3 | +12V
  4 | -5V
  5 | +5V
  6 | Key
  7 | Blue
  8 | Gnd
  9 | Red
 10 | Gnd
 11 | Video (Green + -Sync?)
 12 | Gnd
 
Hinweis: Die Pins 7 & 8, 9 & 10, und 11 & 12 sind als "twisted pair" auf dem
Schaltplan des RGB Interface Boards beschriftet.

 
RGB Interface Board (9-pos, 0.100"?)
(to & from Monitor)
Pin | Definition
------------------
  1 | Gnd [to monitor RGB Gnd]
  2 | Red
  3 | Key
  4 | Gnd
  5 | Green
  6 | Gnd
  7 | Blue
  8 | Gnd [to monitor Sync Gnd]
  9 | -Sync
 
Note: Die Pins 1 & 2, 4 & 5, 6 & 7, und 8 & 9 sind als "twisted pair" auf dem
Schaltplan des RGB Interface Boards beschriftet.
 
 
Audio Amp #2 Board (13-pos, 0.100"?)
(to & from Game Board)
Pin | Definition
------------------
  1 | Audio Return (+16V Gnd) [to PS]
  2 | Audio In #1
  3 | Audio In #2
  4 | Audio In #3
  5 | Key
  6 | Audio Common - GND (Speaker GND)
  7 | +16V [from PS]
  8 | Speaker #1
  9 | Speaker #1
 10 | Speaker #2
 11 | Speaker #2
 12 | Speaker #3
 13 | Speaker #3
 

Hier sind Informationen der PSU (gameside der PSU) - Spare: A082-90411-0000. 
Ein ? bedeutet, daß die Belegung nicht 100% Stimmen muß.
Diese PSU nutzt grundsätzlich die gleichen Ein- und Ausgangsspannungen wie
die PSU in Super Pac-Man (Spare: A082-90421-0000).
 
Power Supply (19-pos?)
1   +V Audio (~13V @ 1.5A)
2   -5V @ 0.45A
3   +V Independent [~10V @ 3.5A, to coin door and control lights?]
4   !Reset
5   V.Batt?
6   Key
7   +12V @ 1.45A
8   +12V @ 1.45A
9   -Sense
10  AC Sync?
11  -V Audio [Gnd for Audio circuit]
12  -V Independent [Gnd, control lights return?]
13  Gnd
14  Gnd
15  Gnd
16  Gnd
17  Coin Counter Drivers (~8V, unreg +5V) [from coin meter]
18  +5V @ 3A
19  +5V @ 2A regulated for logic
 
Feel free to correct any misinformation you find in this pinout.  If you
let me know (holcomb@halcyon.com), I will correct the copy of this pinout
located on wiretap.spies.com.
 
--Dave Holcomb

Zusatzinfo:
 -Übersetzung (v0.1) by Christian Büker '2004 / http://consoles.cbueker.de / contact@cbueker.de
 -Ich hafte *NICHT* für Übersetzungsfehler oder andere Fehler, die sich in den Pinouts befinden können!!
 -Das ursprüngliche Dokument entwart Dave Holcomb (siehe oben). Die Ehre für das Ganze gebührt einzig
  und allein Ihm.


Zurück zur Übersicht.
(c) by Christian Bueker (contact@cbueker.de) | Diese Seite ist Bestandteil von http://consoles.cbueker.de | Back